Difference between revisions of "Getting started with TI Jacinto 7 Edge AI/Introduction/SoM Overview"
(→Configuration) |
(→SOM Overview) |
||
Line 83: | Line 83: | ||
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 | ‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 | ||
|- | |- | ||
− | !colspan="4"|Note: This table is a rework from [https://www.ti.com/lit/ug/spruis4a/spruis4a.pdf?ts=1620938339053&ref_url=https%253A%252F%252Fwww.google.com%252F .]. | + | !colspan="4"|Note: This table is a rework from [https://www.ti.com/lit/ug/spruis4a/spruis4a.pdf?ts=1620938339053&ref_url=https%253A%252F%252Fwww.google.com%252F Jacinto7 DRA829/TDA4VM Evaluation Module (EVM) Users Guide (Rev. A).]]]. |
|} | |} |
Revision as of 13:32, 9 June 2021
SOM Overview
Jacinto 7 System On Module
Features
According to Texas Instruments website, Jacinto 7 SOM has the following features:
- TDA4VM/DRA829V (J721 E) processor
- Optimized power solution (PMIC)
- DRAM, LPDDR4‐3733, 4GByte total memory, support inline ECC
- Octal‐SPI NOR flash, 512Mb memory (8bit)
- HyperFlash + HyerRAM, 512Mb flash memory + 256Mb RAM
Also, it is important to mention that TDA4VM and DRA829V processors heterogeneous architecture includes:
- A mix of fixed and floating-point DSP cores
- Arm® Cortex®-A72 cores
- Matrix math acceleration for machine learning
- Integrated ISP and vision processing acceleration
- 2D and 3D GPU cores
- H.264 encode/H.265 decode acceleration
Board Distribution
For reference on where are located main components and their description, check the following image:
Configuration
The switches SW1, SW2 and SW3 are called configuration switches and
Switch Name | Default Condition | Signal | Operation |
---|---|---|---|
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
SW1.1 | ON | LPDDR4_IO_SEL | Selects the I/O voltage level for LPDDR4:
‘0’ (OFF) = Selects 0.6 V I/O for LPDDR4X,‘1’ (ON) = Selects 1.1 V I/O for LPDDR4 |
Note: This table is a rework from Jacinto7 DRA829/TDA4VM Evaluation Module (EVM) Users Guide (Rev. A).]]. |